View TLC227XA-EP_3492973.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? sgls131b ? july 2002 ? revised december 2003 1 post office box 655303 ? dallas, texas 75265 controlled baseline ? one assembly/test site, one fabrication site extended temperature performance of ?55 c to 125 c enhanced diminishing manufacturing sources (dms) support enhanced product change notification qualification pedigree ? output swing includes both supply rails ? component qualification in accordance with jedec and industry standards to ensure reliable operation over an extended temperature range. this includes, but is not limited to, highly accelerated stress test (hast) or biased 85/85, temperature cycle, autoclave or unbiased hast, electromigration, bond intermetallic life, and mold compound life. such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. low noise ...9 nv/ hz typ at f = 1 khz low input bias current ...1 pa typ fully specified for both single-supply and split-supply operation common-mode input voltage range includes negative rail high-gain bandwidth . . . 2.2 mhz typ high slew rate . . . 3.6 v/ s typ low input offset voltage 950 v max at t a = 25 c macromodel included performance upgrades for the ts272, ts274, tlc272, and tlc274 description the tlc2272a and tlc2274a are dual and quadruple operational amplifiers from texas instruments. both devices exhibit rail-to-rail output performance for increased dynamic range in single- or split-supply applications. the tlc227xa family offers 2 mhz of bandwidth and 3 v/ s of slew rate for higher speed applications. these devices offer comparable ac performance while having better noise, input offset voltage, and power dissipation than existing cmos operational amplifiers. the tlc227xa has a noise voltage of 9 nv/ hz , two times lower than competitive solutions. the tlc227xa, exhibiting high input impedance and low noise, is excellent for small-signal conditioning for high-impedance sources, such as piezoelectric transducers. because of the micro- power dissipation levels, these devices work well in hand-held monitoring and remote-sensing applications. in addition, the rail-to-rail output feature, with single- or split-supplies, makes this family a great choice when interfacing with analog-to-digital converters (adcs). for precision applications, the tlc227xa family has a maximum input offset voltage of 950 v. this family is fully characterized at 5 v and 5 v. the tlc2272/4 also makes great upgrades to the tlc272/4 or ts272/4 in standard designs. they offer increased output dynamic range, lower noise voltage, and lower input offset voltage. this enhanced feature set allows them to be used in a wider range of applications. copyright ? 2003 texas instruments incorporated please be aware that an important notice concerning avail ability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. advanced lincmos is a trademark of texas instruments. |v dd | ? supply voltage ? v 10 8 6 4 46 8 12 14 16 10 12 14 16 maximum peak-to-peak output voltage vs supply voltage t a = 25 c i o = 50 a i o = 500 a v(opp) ? maximum peak-to-peak output voltage ? v v o(pp) copyright ? 2002 ? 2003, texas instruments incorporated please be aware that an important notice concerning avail ability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. advanced lincmos is a trademark of texas instruments.
? sgls131a ? july 2002 ? revised november 2003 2 post office box 655303 ? dallas, texas 75265 available options packaged devices t a v io max at 25 c small outline (d) tssop (pw) ?55 c to 125 c 950 v tlc2272amdrep tlc2272ampwrep ?55 c to 125 c 950 v 2.5 mv tlc2272amdrep tlc2272mdrep tlc2272ampwrep tlc2272mpwrep ?55 c to 125 c 950 v tlc2274amdrep tlc2274ampwrep ?55 c to 125 c 950 v 2.5 mv tlc2274amdrep tlc2274mdrep tlc2274ampwrep tlc2274mpwrep 1 2 3 4 8 7 6 5 1out 1in ? 1in + v dd ? /gnd v dd + 2out 2in ? 2in + tlc2272 d or pw package (top view) 1 2 3 4 5 6 7 14 13 12 11 10 9 8 1out 1in ? 1in + v dd + 2in + 2in ? 2out 4out 4in ? 4in + v dd ? 3in + 3in ? 3out tlc2274 d or pw package (top view)
? sgls131a ? july 2002 ? revised november 2003 3 post office box 655303 ? dallas, texas 75265 equivalent schematic (each amplifier) q3 q6 q9 q12 q14 q16 q2 q5 q7 q8 q10 q11 d1 q17 q15 q13 q4 q1 r5 c1 v dd + in + in ? r3 r4 r1 r2 out v dd? actual device component count ? component tlc2272 tlc2274 transistors 38 76 resistors 26 52 diodes 9 18 capacitors 3 6 ? includes both amplifiers and all esd, bias, and trim circuitry
? sgls131a ? july 2002 ? revised november 2003 4 post office box 655303 ? dallas, texas 75265 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) ? supply voltage, v dd + (see note 1) 8 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . supply voltage, v dd ? (see note 1) ?8 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . differential input voltage, v id (see note 2) 16 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . input voltage range, v i (any input, see note 1) v dd? ? 0.3 v to v dd+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . input current, i i (any input) 5 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . output current, i o 50 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . total current into v dd + 50 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . total current out of v dd ? 50 ma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . duration of short-circuit current at (or below) 25 c (see note 3) unlimited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . continuous total dissipation see dissipation rating table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . operating free-air temperature range, t a ?55 c to 125 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . storage temperature range (see note 4) ?65 c to 150 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: d or pw package 260 c . . . . . . . . . . . . . . . ? stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. these are stress ratings only, a nd functional operation of the device at these or any other conditions beyond those indicated under ?recommended operating conditi ons? is not implied. exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. notes: 1. all voltage values, except differential voltages, are with respect to the midpoint between v dd+ and v dd ? . 2. differential voltages are at in+ with respect to in ?. excessive current will flow if input is brought below v dd ? ? 0.3 v. 3. the output may be shorted to either supply. temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. 4. long term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. see http://www.ti.com/ep_quality for additional information on enhanced plastic packaging. dissipation rating table package t a 25 c derating factor t a = 70 c t a = 85 c t a = 125 c package t a 25 c power rating derating factor above t a = 25 c t a = 70 c power rating t a = 85 c power rating t a = 125 c power rating d-8 725 mw 5.8 mw/ c 464 mw 337 mw 145 mw d-14 950 mw 7.6 mw/ c 608 mw 494 mw 190 mw pw-8 525 mw 4.2 mw/ c 336 mw 273 mw 105 mw pw-14 700 mw 5.6 mw/ c 448 mw 364 mw ? recommended operating conditions min max unit min max unit supply voltage, v dd 2.2 8 v input voltage, v i v dd ? v dd + ? 1.5 v common-mode input voltage, v ic v dd ? v dd + ? 1.5 v operating free-air temperature, t a ?55 125 c
? sgls131a ? july 2002 ? revised november 2003 5 post office box 655303 ? dallas, texas 75265 tlc2272-ep electrical characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? tlc2272-ep tlc2272a-ep unit parameter test conditions t a ? min typ max min typ max unit v io input offset voltage 25 c 300 2500 300 950 v v io input offset voltage full range 3000 1500 v vio temperature coefficient 25 c 2 2 v/ c vio temperature coefficient of input offset voltage 25 c to 125 c 2 2 v/ c input offset voltage long- term drift (see note 5) v ic = 0 v, v o = 0 v, v dd = 2.5 v , r s = 50 ? 25 c 0.002 0.002 v/mo i io input offset current v o = 0 v, r s = 50 ? c 0.5 60 0.5 60 pa i io input offset current full range 800 800 pa i ib input bias current 25 c 1 60 1 60 pa i ib input bias current full range 800 800 pa v icr common-mode input r s = 50 ? | v io | 5 mv 25 c 0 to 4 ?0.3 to 4.2 0 to 4 ?0.3 to 4.2 v v icr common-mode input voltage r s = 50 ?, | v io | 5 mv full range 0 to 3.5 0 to 3.5 v i oh = ? 20 a 25 c 4.99 4.99 high-level output i oh = ? 200 a 25 c 4.85 4.93 4.85 4.93 v oh high-level output voltage i oh = ? 200 a full range 4.85 4.85 v v oh voltage i oh = ? 1 ma 25 c 4.25 4.65 4.25 4.65 v i oh = ? 1 ma full range 4.25 4.25 v ic = 2.5 v, i ol = 50 a 25 c 0.01 0.01 v ic = 2.5 v, i ol = 500 a 25 c 0.09 0.15 0.09 0.15 v ol low-level output voltage v ic = 2.5 v, i ol = 500 a full range 0.15 0.15 v v ol low-level output voltage v ic = 2.5 v, i ol = 5 a 25 c 0.9 1.5 0.9 1.5 v v ic = 2.5 v, i ol = 5 a full range 1.5 1.5 large-signal v ic = 2.5 v, r l = 10 k ? ? 25 c 10 35 10 35 a vd large-signal differential voltage v ic = 2.5 v, v o = 1 v to 4 v r l = 10 k ? ? full range 10 10 v/mv a vd differential voltage amplification v o = 1 v to 4 v r l = 1 m ? ? 25 c 175 175 v/mv r id differential input resistance 25 c 10 12 10 12 ? r i common-mode input resistance 25 c 10 12 10 12 ? c i common-mode input capacitance f = 10 khz, p package 25 c 8 8 pf z o closed-loop output impedance f = 1 mhz, a v = 10 25 c 140 140 ? cmrr common-mode rejection v ic = 0 v to 2.7 v, 25 c 70 75 70 75 db cmrr common-mode rejection ratio v ic = 0 v to 2.7 v, v o = 2.5 v, r s = 50 ? full range 70 70 db k svr supply-voltage rejection v dd = 4.4 v to 16 v, 25 c 80 95 80 95 db k svr supply-voltage rejection ratio ( ? v dd / ? v io ) v dd = 4.4 v to 16 v, v ic = v dd /2, no load full range 80 80 db i dd supply current v o = 2.5 v, no load 25 c 2.2 3 2.2 3 ma i dd supply current v o = 2.5 v, no load full range 3 3 ma ? full range is ?55 c to 125 c for m level part. ? referenced to 2.5 v note 5: typical values are based on the input offset voltage shift observed through 168 hours of operating life test at t a = 150 c extrapolated to t a = 25 c using the arrhenius equation and assuming an activation energy of 0.96 ev.
? sgls131a ? july 2002 ? revised november 2003 6 post office box 655303 ? dallas, texas 75265 tlc2272-ep operating characteristics at specified free-air temperature, v dd = 5 v parameter test conditions t a ? tlc2272-ep tlc2272a-ep unit parameter test conditions t a ? min typ max min typ max unit slew rate at v o = 1.25 v to 2.75 v, 25 c 2.3 3.6 2.3 3.6 sr slew rate at unity gain v o = 1.25 v to 2.75 v, r l = 10 k ? ?, c l = 100 pf ? full 1.7 1.7 v/ s sr unity gain r l = 10 k ? ?, c l = 100 pf ? full range 1.7 1.7 v/ s v n equivalent input f = 10 hz 25 c 50 50 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 9 9 nv/ hz v npp peak-to-peak equivalent input f = 0.1 hz to 1 hz 25 c 1 1 v v npp equivalent input noise voltage f = 0.1 hz to 10 hz 25 c 1.4 1.4 v i n equivalent input noise current 25 c 0.6 0.6 fa/ hz total harmonic v o = 0.5 v to 2.5 v, a v = 1 0.0013% 0.0013% thd + n total harmonic distortion plus noise v o = 0.5 v to 2.5 v, f = 20 khz, r = 10 k ? , a v = 10 25 c 0.004% 0.004% thd + n distortion plus noise f = 20 khz, r l = 10 k ? ? , a v = 100 25 c 0.03% 0.03% gain-bandwidth f = 10 khz, r l = 10 k ? ? , 25 c 2.18 2.18 mhz gain-bandwidth product f = 10 khz, c l = 100 pf ? r l = 10 k ? ? , 25 c 2.18 2.18 mhz b om maximum output- v o(pp) = 2 v, ? a v = 1, ? 25 c 1 1 mhz b om maximum output- swing bandwidth v o(pp) = 2 v, r l = 10 k ? ? , a v = 1, c l = 100 pf ? 25 c 1 1 mhz a v = ? 1, to 0.1% 1.5 1.5 t s settling time a v = ? 1, step = 0.5 v to 2.5 v, ? to 0.1% 25 c 1.5 1.5 s t s settling time step = 0.5 v to 2.5 v, r l = 10 k ? ? , ? to 0.01% 25 c 2.6 2.6 s s r l = 10 k ? ? , c l = 100 pf ? to 0.01% 2.6 2.6 m phase margin at unity gain r l = 10 k ? ? , c l = 100 pf ? 25 c 50 50 gain margin r l = 10 k ? ? , c l = 100 pf ? 25 c 10 10 db ? full range is ?55 c to 125 c for m level part. ? referenced to 2.5 v
? sgls131a ? july 2002 ? revised november 2003 7 post office box 655303 ? dallas, texas 75265 tlc2272-ep electrical characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? tlc2272-ep tlc2272a-ep unit parameter test conditions t a ? min typ max min typ max unit v io input offset voltage 25 c 300 2500 300 950 v v io input offset voltage full range 3000 1500 v vio temperature coefficient of 25 c 2 2 v/ c vio temperature coefficient of input offset voltage 25 c to 125 c 2 2 v/ c input offset voltage long-term drift (see note 5) v ic = 0 v, r s = 50 ? v o = 0 v, 25 c 0.002 0.002 v/mo i io input offset current s 25 c 0.5 60 0.5 60 pa i io input offset current full range 800 800 pa i ib input bias current 25 c 1 60 1 60 pa i ib input bias current full range 800 800 pa 25 c ?5 ?5.3 ?5 ?5.3 common-mode input 25 c ?5 to 4 ?5.3 to 4.2 ?5 to 4 ?5.3 to 4.2 v icr common-mode input r s = 50 ? | v io | 5 mv 25 c to 4 to 4.2 to 4 to 4.2 v v icr common-mode input voltage r s = 50 ?, | v io | 5 mv full range ?5 ?5 v v icr voltage r s = 50 , | v io | 5 mv full range ?5 to 3.5 ?5 to 3.5 v full range to 3.5 to 3.5 i o = ? 20 a 25 c 4.99 4.99 maximum positive peak i o = ? 200 a 25 c 4.85 4.93 4.85 4.93 v om + maximum positive peak output voltage i o = ? 200 a full range 4.85 4.85 v v om + output voltage i o = ? 1 ma 25 c 4.25 4.65 4.25 4.65 v i o = ? 1 ma full range 4.25 4.25 v ic = 0 v, i o = 50 a 25 c ?4.99 ?4.99 maximum negative peak v ic = 0 v, i o = 500 a 25 c ?4.85 ?4.91 ?4.85 ?4.91 v om ? maximum negative peak output voltage v ic = 0 v, i o = 500 a full range ?4.85 ?4.85 v v om ? output voltage v ic = 0 v, i o = 5 a 25 c ?3.5 ?4.1 ?3.5 ?4.1 v v ic = 0 v, i o = 5 a full range ?3.5 ?3.5 large-signal differential r l = 10 k ? c 20 50 20 50 a vd large-signal differential voltage amplification v o = 4 v r l = 10 k ? full range 20 20 v/mv a vd voltage amplification v o = 4 v r l = 1 m ? 25 c 300 300 v/mv r id differential input resistance 25 c 10 12 10 12 ? r i common-mode input resistance 25 c 10 12 10 12 ? c i common-mode input capacitance f = 10 khz, p package 25 c 8 8 pf z o closed-loop output impedance f = 1 mhz, a v = 10 25 c 130 130 ? cmrr common-mode rejection v ic = ? 5 v to 2.7 v, 25 c 75 80 75 80 db cmrr common-mode rejection ratio v ic = ? 5 v to 2.7 v, v o = 0 v, r s = 50 ? full range 75 75 db k svr supply-voltage rejection v dd = 2.2 v to 8 v, 25 c 80 95 80 95 db k svr supply-voltage rejection ratio ( ? v dd / ? v io ) v dd = 2.2 v to 8 v, v ic = 0 v, no load full range 80 80 db i dd supply current v o = 2.5 v, no load 25 c 2.4 3 2.4 3 ma i dd supply current v o = 2.5 v, no load full range 3 3 ma ? full range is ?55 c to 125 c for m level part. note 5: typical values are based on the input offset voltage shift observed through 168 hours of operating life test at t a = 150 c extrapolated to t a = 25 c using the arrhenius equation and assuming an activation energy of 0.96 ev.
? sgls131a ? july 2002 ? revised november 2003 8 post office box 655303 ? dallas, texas 75265 tlc2272-ep operating characteristics at specified free-air temperature, v dd = 5 v parameter test conditions t a ? tlc2272-ep tlc2272a-ep unit parameter test conditions t a ? min typ max min typ max unit slew rate at v o = 1 v, r l = 10 k ? , 25 c 2.3 3.6 2.3 3.6 sr slew rate at unity gain v o = 1 v, r l = 10 k ? , c l = 100 pf full 1.7 1.7 v/ s sr unity gain c l = 100 pf full range 1.7 1.7 v/ s v n equivalent input f = 10 hz 25 c 50 50 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 9 9 nv/ hz v npp peak-to-peak equivalent input f = 0.1 hz to 1 hz 25 c 1 1 v v npp equivalent input noise voltage f = 0.1 hz to 10 hz 25 c 1.4 1.4 v i n equivalent input noise current 25 c 0.6 0.6 fa/ hz total harmonic v o = 2.3 v a v = 1 0.0011% 0.0011% thd + n total harmonic distortion plus noise v o = 2.3 v r l = 10 k ?, f = 20 khz a v = 10 25 c 0.004% 0.004% thd + n distortion plus noise r l = 10 k ?, , ? , 25 c 2.25 2.25 mhz gain-bandwidth product f = 10 khz, c l = 100 pf r l = 10 k ? , 25 c 2.25 2.25 mhz b om maximum output-swing v o(pp) = 4.6 v, a v = 1, 25 c 0.54 0.54 mhz b om output-swing bandwidth v o(pp) = 4.6 v, r l = 10 k ? , a v = 1, c l = 100 pf 25 c 0.54 0.54 mhz a v = ? 1, to 0.1% 1.5 1.5 t s settling time a v = ? 1, step = ? 2.3 v to 2.3 v, to 0.1% 25 c 1.5 1.5 s t s settling time step = ? 2.3 v to 2.3 v, r l = 10 k ? , to 0.01% 25 c 3.2 3.2 s s r l = 10 k ? , c l = 100 pf to 0.01% 3.2 3.2 m phase margin at unity gain r l = 10 k ? , c l = 100 pf 25 c 52 52 gain margin r l = 10 k ? , c l = 100 pf 25 c 10 10 db ? full range is ?55 c to 125 c for m level part.
? sgls131a ? july 2002 ? revised november 2003 9 post office box 655303 ? dallas, texas 75265 tlc2274-ep electrical characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? tlc2274-ep tlc2274a-ep unit parameter test conditions t a ? min typ max min typ max unit v io input offset voltage 25 c 300 2500 300 950 v v io input offset voltage full range 3000 1500 v vio temperature coefficient 25 c 2 2 v/ c vio temperature coefficient of input offset voltage 25 c to 125 c 2 2 v/ c input offset voltage long-term drift (see note 5) v dd = 2.5 v , v o = 0 v, v ic = 0 v, r s = 50 ? 25 c 0.002 0.002 v/mo i io input offset current o s 25 c 0.5 60 0.5 60 pa i io input offset current full range 800 800 pa i ib input bias current 25 c 1 60 1 60 pa i ib input bias current full range 800 800 pa 25 c 0 ?0.3 0 ?0.3 common-mode input 25 c 0 to 4 ?0.3 to 4.2 0 to 4 ?0.3 to 4.2 v icr common-mode input r s = 50 ? | v io | 5 mv 25 c to 4 to 4.2 to 4 to 4.2 v v icr common-mode input voltage r s = 50 ?, | v io | 5 mv full range 0 to 0 to v v icr voltage r s = 50 , | v io | 5 mv full range 0 to 3.5 0 to 3.5 v full range 3.5 3.5 i oh = ? 20 a 25 c 4.99 4.99 high-level output i oh = ? 200 a 25 c 4.85 4.93 4.85 4.93 v oh high-level output voltage i oh = ? 200 a full range 4.85 4.85 v v oh voltage i oh = ? 1 ma 25 c 4.25 4.65 4.25 4.65 v i oh = ? 1 ma full range 4.25 4.25 v ic = 2.5 v, i ol = 50 a 25 c 0.01 0.01 low-level output v ic = 2.5 v, 25 c 0.09 0.15 0.09 0.15 v ol low-level output voltage v ic = 2.5 v, i ol = 500 a full range 0.15 0.15 v v ol voltage v ic = 2.5 v, i ol = 5 a 25 c 0.9 1.5 0.9 1.5 v v ic = 2.5 v, i ol = 5 a full range 1.5 1.5 large-signal differential v ic = 2.5 v, r l = 10 k ? ? 25 c 10 35 10 35 a vd large-signal differential voltage amplification v ic = 2.5 v, v o = 1 v to 4 v r l = 10 k ? ? full range 10 10 v/mv a vd voltage amplification v o = 1 v to 4 v r l = 1 m ? ? 25 c 175 175 v/mv r id differential input resistance 25 c 10 12 10 12 ? r i common-mode input resistance 25 c 10 12 10 12 ? c i common-mode input capacitance f = 10 khz, n package 25 c 8 8 pf z o closed-loop output impedance f = 1 mhz, a v = 10 25 c 140 140 ? cmrr common-mode v ic = 0 v to 2.7 v, 25 c 70 75 70 75 db cmrr common-mode rejection ratio v ic = 0 v to 2.7 v, v o = 2.5 v, r s = 50 ? full range 70 70 db k svr supply-voltage rejection v dd = 4.4 v to 16 v, 25 c 80 95 80 95 db k svr supply-voltage rejection ratio ( ? v dd / ? v io ) v dd = 4.4 v to 16 v, v ic = v dd /2, no load full range 80 80 db i dd supply current v o = 2.5 v, no load 25 c 4.4 6 4.4 6 ma i dd supply current v o = 2.5 v, no load full range 6 6 ma ? full range is ?55 c to 125 c for m level part. ? referenced to 2.5 v note 5: typical values are based on the input offset voltage shift observed through 168 hours of operating life test at t a = 150 c extrapolated to t a = 25 c using the arrhenius equation and assuming an activation energy of 0.96 ev.
? sgls131a ? july 2002 ? revised november 2003 10 post office box 655303 ? dallas, texas 75265 tlc2274-ep operating characteristics at specified free-air temperature, v dd = 5 v parameter test conditions t a ? tlc2274-ep tlc2274a-ep unit parameter test conditions t a ? min typ max min typ max unit slew rate at unity v o = 0.5 v to 2.5 v, c l = 100 pf ? 25 c 2.3 3.6 2.3 3.6 sr slew rate at unity gain v o = 0.5 v to 2.5 v, r l = 10 k ? ? , c l = 100 pf ? full 1.7 1.7 v/ s sr gain r l = 10 k ? ? , full range 1.7 1.7 v/ s v n equivalent input f = 10 hz 25 c 50 50 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 9 9 nv/ hz v n(pp) peak-to-peak equivalent input f = 0.1 hz to 1 hz 25 c 1 1 v v n(pp) equivalent input noise voltage f = 0.1 hz to 10 hz 25 c 1.4 1.4 v i n equivalent input noise current 25 c 0.6 0.6 fa / hz total harmonic v o = 0.5 v to 2.5 v, a v = 1 0.0013% 0.0013% thd + n total harmonic distortion plus noise v o = 0.5 v to 2.5 v, f = 20 khz, r = 10 k ? a v = 10 25 c 0.004% 0.004% thd + n distortion plus noise f = 20 khz, r l = 10 k ? ? a v = 100 25 c 0.03% 0.03% gain-bandwidth f = 10 khz, r l = 10 k ? ? , 25 c 2.18 2.18 mhz gain-bandwidth product f = 10 khz, c l = 100 pf ? r l = 10 k ? ? , 25 c 2.18 2.18 mhz b om maximum out- put-swing band- v o(pp) = 2 v, ? a v = 1, ? 25 c 1 1 mhz b om put-swing band- width v o(pp) = 2 v, r l = 10 k ? ? , a v = 1, c l = 100 pf ? 25 c 1 1 mhz a v = ? 1, to 0.1% 1.5 1.5 t s settling time a v = ? 1, step = 0.5 v to 2.5 v, ? to 0.1% 25 c 1.5 1.5 s t s settling time step = 0.5 v to 2.5 v, r l = 10 k ? ? , ? to 0.01% 25 c 2.6 2.6 s s r l = 10 k ? ? , c l = 100 pf ? to 0.01% 2.6 2.6 m phase margin at unity gain r l = 10 k ? ? , c l = 100 pf ? 25 c 50 50 gain margin r l = 10 k ? ? , c l = 100 pf ? 25 c 10 10 db ? full range is ?55 c to 125 c for m level part. ? referenced to 2.5 v
? sgls131a ? july 2002 ? revised november 2003 11 post office box 655303 ? dallas, texas 75265 tlc2274-ep electrical characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? tlc2274-ep tlc2274a-ep unit parameter test conditions t a ? min typ max min typ max unit v io input offset voltage 25 c 300 2500 300 950 v v io input offset voltage full range 3000 1500 v vio temperature coefficient of 25 c 2 2 v/ c vio temperature coefficient of input offset voltage 25 c to 125 c 2 2 v/ c input offset voltage long- term drift (see note 5) v ic = 0 v, r s = 50 ? v o = 0 v, 25 c 0.002 0.002 v/mo i io input offset current r s = 50 ? c 0.5 60 0.5 60 pa i io input offset current full range 800 800 pa i ib input bias current 25 c 1 60 1 60 pa i ib input bias current full range 800 800 pa ?5 ?5.3 ?5 ?5.3 common-mode input 25 c ?5 to 4 ?5.3 to 4.2 ?5 to 4 ?5.3 to 4.2 v icr common-mode input r s = 50 ? | v io | 5 mv 25 c to 4 to 4.2 to 4 to 4.2 v v icr common-mode input voltage r s = 50 ?, | v io | 5 mv ?5 ?5 v v icr voltage r s = 50 , | v io | 5 mv full range ?5 to 3.5 ?5 to 3.5 v full range to 3.5 to 3.5 i o = ? 20 a 25 c 4.99 4.99 maximum positive peak i o = ? 200 a 25 c 4.85 4.93 4.85 4.93 v om + maximum positive peak output voltage i o = ? 200 a full range 4.85 4.85 v v om + output voltage i o = ? 1 ma 25 c 4.25 4.65 4.25 4.65 v i o = ? 1 ma full range 4.25 4.25 v ic = 0 v, i o = 50 a 25 c ?4.99 ?4.99 maximum negative peak v ic = 0 v, i o = 500 a 25 c ?4.85 ?4.91 ?4.85 ?4.91 v om ? maximum negative peak output voltage v ic = 0 v, i o = 500 a full range ?4.85 ?4.85 v v om ? output voltage v ic = 0 v, i o = 5 a 25 c ?3.5 ?4.1 ?3.5 ?4.1 v v ic = 0 v, i o = 5 a full range ?3.5 ?3.5 large-signal differential r l = 10 k ? c 20 50 20 50 a vd large-signal differential voltage amplification v o = 4 v r l = 10 k ? full range 20 20 v/mv a vd voltage amplification v o = 4 v r l = 1 m ? 25 c 300 300 v/mv r id differential input resistance 25 c 10 12 10 12 ? r i common-mode input resistance 25 c 10 12 10 12 ? c i common-mode input capacitance f = 10 khz, n package 25 c 8 8 pf z o closed-loop output impedance f = 1 mhz, a v = 10 25 c 130 130 ? cmrr common-mode rejection v ic = ? 5 v to 2.7 v 25 c 75 80 75 80 db cmrr common-mode rejection ratio v ic = ? 5 v to 2.7 v v o = 0 v, r s = 50 ? full range 75 75 db k svr supply-voltage rejection v dd = 2.2 v to 8 v, 25 c 80 95 80 95 db k svr supply-voltage rejection ratio ( ? v dd / ? v io ) v dd = 2.2 v to 8 v, v ic = 0 v, no load full range 80 80 db i dd supply current v o = 0 v, no load 25 c 4.8 6 4.8 6 ma i dd supply current v o = 0 v, no load full range 6 6 ma ? full range is ?55 c to 125 c for m level part. note 5: typical values are based on the input offset voltage shift observed through 168 hours of operating life test at t a = 150 c extrapolated to t a = 25 c using the arrhenius equation and assuming an activation energy of 0.96 ev.
? sgls131a ? july 2002 ? revised november 2003 12 post office box 655303 ? dallas, texas 75265 tlc2274-ep operating characteristics at specified free-air temperature, v dd = 5 v parameter test conditions t a ? tlc2274-ep tlc2274a-ep unit parameter test conditions t a ? min typ max min typ max unit slew rate at unity v o = 2.3 v, r l = 10 k ? , 25 c 2.3 3.6 2.3 3.6 sr slew rate at unity gain v o = 2.3 v, c l = 100 pf r l = 10 k ? , full 1.7 1.7 v/ s sr gain c l = 100 pf full range 1.7 1.7 v/ s v n equivalent input f = 10 hz 25 c 50 50 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 9 9 nv/ hz v n(pp) peak-to-peak equivalent input f = 0.1 hz to 1 hz 25 c 1 1 v v n(pp) equivalent input noise voltage f = 0.1 hz to 10 hz 25 c 1.4 1.4 v i n equivalent input noise current 25 c 0.6 0.6 fa / hz total harmonic v o = 2.3 v, a v = 1 0.0011% 0.0011% thd + n total harmonic distortion plus noise v o = 2.3 v, r l = 10 k ?, f = 20 khz a v = 10 25 c 0.004% 0.004% thd + n distortion plus noise r l = 10 k ?, , ? , 25 c 2.25 2.25 mhz gain-bandwidth product f = 10 khz, c l = 100 pf r l = 10 k ? , 25 c 2.25 2.25 mhz b om maximum output-swing v o(pp) = 4.6 v, a v = 1, 25 c 0.54 0.54 mhz b om output-swing bandwidth v o(pp) = 4.6 v, r l = 10 k ? , a v = 1, c l = 100 pf 25 c 0.54 0.54 mhz a v = ? 1, to 0.1% 1.5 1.5 t s settling time a v = ? 1, step = ? 2.3 v to 2.3 v, to 0.1% 25 c 1.5 1.5 s t s settling time step = ? 2.3 v to 2.3 v, r l = 10 k ? , to 0.01% 25 c 3.2 3.2 s s r l = 10 k ? , c l = 100 pf to 0.01% 3.2 3.2 m phase margin at unit gain r l = 10 k ? , c l = 100 pf 25 c 52 52 gain margin r l = 10 k ? , c l = 100 pf 25 c 10 10 db ? full range is ?55 c to 125 c for m level part.
? sgls131a ? july 2002 ? revised november 2003 13 post office box 655303 ? dallas, texas 75265 typical characteristics table of graphs figure v io input offset voltage distribution 1 ? 4 v io input offset voltage distribution vs common-mode voltage 1 ? 4 5, 6 vio input offset voltage temperature coefficient distribution 7 ? 10 i ib /i io input bias and input offset current vs free-air temperature 11 v i input voltage vs supply voltage 12 v i input voltage vs supply voltage vs free-air temperature 12 13 v oh high-level output voltage vs high-level output current 14 v ol low-level output voltage vs low-level output current 15, 16 v om + maximum positive peak output voltage vs output current 17 v om ? maximum negative peak output voltage vs output current 18 v o(pp) maximum peak-to-peak output voltage vs frequency 19 i os short-circuit output current vs supply voltage 20 i os short-circuit output current vs supply voltage vs free-air temperature 20 21 v o output voltage vs differential input voltage 22, 23 large-signal differential voltage amplification vs load resistance 24 a vd large-signal differential voltage amplification and phase margin vs frequency 25, 26 large-signal differential voltage amplification vs free-air temperature 27, 28 z o output impedance vs frequency 29, 30 cmrr common-mode rejection ratio vs frequency 31 cmrr common-mode rejection ratio vs frequency vs free-air temperature 31 32 k svr supply-voltage rejection ratio vs frequency 33, 34 k svr supply-voltage rejection ratio vs frequency vs free-air temperature 33, 34 35 i dd supply current vs supply voltage 36, 37 i dd supply current vs supply voltage vs free-air temperature 36, 37 38, 39 sr slew rate vs load capacitance 40 sr slew rate vs load capacitance vs free-air temperature 40 41 inverting large-signal pulse response 42, 43 v o voltage-follower large-signal pulse response 44, 45 v o inverting small-signal pulse response 46, 47 voltage-follower small-signal pulse response 48, 49 v n equivalent input noise voltage vs frequency 50, 51 noise voltage over a 10-second period 52 integrated noise voltage vs frequency 53 thd + n total harmonic distortion plus noise vs frequency 54 gain-bandwidth product vs supply voltage 55 gain-bandwidth product vs supply voltage vs free-air temperature 55 56 m phase margin vs load capacitance 57 gain margin vs load capacitance 58 note: for all graphs where v dd = 5 v, all loads are referenced to 2.5 v.
? sgls131a ? july 2002 ? revised november 2003 14 post office box 655303 ? dallas, texas 75265 typical characteristics v io ? input offset voltage ? mv percentage of amplifiers ? % distribution of tlc2272 input offset voltage 10 5 0 20 15 ?1.6 ?1.2 0 0.4 0.8 1.2 1.6 891 amplifiers from ?0.8 ?0.4 2 wafer lots v dd = 2.5 v t a = 25 c figure 1 v io ? input offset voltage ? mv percentage of amplifiers ? % distribution of tlc2272 input offset voltage 10 5 0 20 15 ?1.6 ?1.2 0 0.4 0.8 1.2 1.6 ?0.8 ?0.4 891 amplifiers from 2 wafer lots v dd = 5 v t a = 25 c figure 2 figure 3 v io ? input offset voltage ? mv percentage of amplifiers ? % distribution of tlc2274 input offset voltage 10 5 0 20 15 0 0.4 0.8 1.2 1.6 992 amplifiers from ?1.6 ?1.2 ?0.8 ?0.4 2 wafer lots v dd = 2.5 v figure 4 v io ? input offset voltage ? mv percentage of amplifiers ? % distribution of tlc2274 input offset voltage 10 5 0 20 15 0 0.4 0.8 1.2 1.6 992 amplifiers from ?1.6 ?1.2 ?0.8 ?0.4 2 wafer lots v dd = 5 v
? sgls131a ? july 2002 ? revised november 2003 15 post office box 655303 ? dallas, texas 75265 typical characteristics 0.5 0 ?1 ?1 0 1 vio ? input offset voltage ? mv 1 234 5 v io v ic ? common-mode voltage ? v v dd = 5 v t a = 25 c r s = 50 ? ?0.5 input offset voltage vs common-mode voltage figure 5 0.5 0 ?1 ?1 0 1 vio ? input offset voltage ? mv 1 234 5 input offset voltage vs common-mode voltage v ic ? common-mode voltage ? v v io ?0.5 v dd = 5 v t a = 25 c r s = 50 ? ?6 ?5 ?4 ?3 ?2 figure 6 15 10 5 0 ?1 0 1 percentage of amplifiers ? % 20 25 2345 distribution of tlc2272 vs input offset voltage temperature coefficient ? v io ? temperature coefficient ? v/ c 128 amplifiers from 2 wafer lots v dd = 2.5 v p package 25 c to 125 c ?5 ?4 ?3 ?2 figure 7 ?5 ?4 ?3 ?2 15 10 5 0 ?1 0 1 percentage of amplifiers ? % 20 25 2345 distribution of tlc2272 vs input offset voltage temperature coefficient ? v io ? temperature coefficient ? v/ c 128 amplifiers from 2 wafer lots v dd = 5 v p package 25 c to 125 c figure 8 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 16 post office box 655303 ? dallas, texas 75265 typical characteristics 15 10 5 0 01 percentage of amplifiers ? % 20 25 2345 distribution of tlc2274 vs input offset voltage temperature coefficient ? vio ? temperature coefficient ? v/ c ?5 ?4 ?3 ?2 ?1 128 amplifiers from 2 wafer lots v dd = 2.5 v n package t a = 25 c to 125 c figure 9 15 10 5 0 percentage of amplifiers ? % 20 25 distribution of tlc2274 vs input offset voltage temperature coefficient ? vio ? temperature coefficient ? v/ c 012345 ?5 ?4 ?3 ?2 ?1 128 amplifiers from 2 wafer lots v dd = 2.5 v n package t a = 25 c to 125 c figure 10 15 10 5 0 25 45 65 85 20 25 30 105 125 input bias and input offset current ? vs free-air temperature t a ? free-air temperature ? c 35 v dd = 2.5 v v ic = 0 v v o = 0 v r s = 50 ? i ib i io iib and iio ? input bias and input offset currents ? pa ib i i io figure 11 0 ? 2 ? 6 ? 8 ? 10 8 ? 4 2345678 ? input voltage ? v 4 2 6 10 input voltage vs supply voltage |v dd | ? supply voltage ? v v i t a = 25 c r s = 50 ? |v io | 5mv 12 figure 12 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 17 post office box 655303 ? dallas, texas 75265 typical characteristics ?75 ? 25 0 25 50 75 100 125 2 1 0 ?1 3 4 5 ? input voltage ? v v i input voltage ? vs free-air temperature t a ? free-air temperature ? c |v io | 5mv v dd = 5 v ?50 figure 13 v0h ? high-level output voltage ? v v oh i oh ? high-level output current ? ma 4 2 1 0 6 3 01 23 4 5 high-level output voltage ? vs high-level output current v dd = 5 v t a = 125 c t a = ? 55 c t a = 25 c figure 14 vol ? low-level output voltage ? v 0.6 0.4 0.2 0 0123 0.8 45 v dd = 5 v t a = 25 c i ol ? low-level output current ? ma v ol v ic = 1.25 v low-level output voltage vs low-level output current 1 1.2 v ic = 2.5 v figure 15 v ic = 0 v low-level output voltage ? vs low-level output current vol ? low-level output voltage ? v i ol ? low-level output current ? ma v ol 0.6 0.4 0.2 0 0123 0.8 4 1 1.2 56 1.4 v dd = 5 v v ic = 2.5 v t a = 125 c t a = 25 c t a = ? 55 c figure 16 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 18 post office box 655303 ? dallas, texas 75265 typical characteristics 3 2 1 01 2 3 4 5 ? maximum positive peak output voltage ? v 4 5 maximum positive peak output voltage ? vs output current |i o | ? output current ? ma t a = ? 55 c t a = 25 c t a = 125 c v dd = 5 v v om + figure 17 012345 6 i o ? output current ? ma maximum negative peak output voltage ? vs output current v dd = 5 v v ic = 0 v t a = 125 c t a = 25 c t a = ? 55 c ?3.8 ?4 ?4.2 ?4.4 ?4.6 ?4.8 ?5 ? maximum negative peak output voltage ? v v om ? figure 18 figure 19 2 1 0 10 k 100 k 1 m 3 f ? frequency ? hz 4 10 m 6 5 7 8 9 10 maximum peak-to-peak output voltage vs frequency v(opp) ? maximum peak-to-peak output voltage ? v v o(pp) v dd = 5 v v dd = 5 v r l = 10 k ? t a = 25 c figure 20 4 0 23 4 8 12 16 567 8 ios ? short-circuit output current ? ma os i |v dd | ? supply voltage ? v short-circuit output current vs supply voltage v id = 100 mv v o = 0 v t a = 25 c ?8 v id = ? 100 mv ?4 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 19 post office box 655303 ? dallas, texas 75265 typical characteristics ?5 short-circuit output current ? vs free-air temperature ?75 ?50 ?25 0 25 50 75 100 125 ?1 ?3 7 11 15 ios ? short-circuit output current ? ma os i t a ? free-air temperature ? c v id = 100 mv v id = ? 100 mv v o = 0 v v dd = 5 v figure 21 output voltage vs differential input voltage 3 2 1 0 800 4 5 1200 v id ? differential input voltage ? v ? output voltage ? v v o ?800 ?400 400 0 v dd = 5 v t a = 25 c r l = 10 k ? v ic = 2.5 v figure 22 1 ?1 ?3 ?5 0 250 3 5 output voltage vs differential input voltage 500 750 1000 v id ? differential input voltage ? v ? output voltage ? v v o ?1000 ?750 ?250 ?500 figure 23 v dd = 5 v t a = 25 c r l = 10 k ? v ic = 0 v 0.1 1 0.1 1 10 100 10 100 1000 large-signal differential voltage amplification vs load resistance r l ? load resistance ? k ? v o = 1 v t a = 25 c v dd = 5 v v dd = 5 v figure 24 avd ? large-signal differential ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 20 post office box 655303 ? dallas, texas 75265 typical characteristics 0 20 1 k 10 k 100 k 1 m 40 60 80 large-signal differential voltage amplification and phase margin vs frequency f ? frequency ? hz 10 m om ? phase margin m v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c ?20 ?40 ?90 ?45 0 45 90 135 180 avd ? large-signal differential 5 v r l = 10 k ? c l = 100 pf t a = 25 c om ? phase margin m ?20 ?40 ?90 ?45 0 45 90 135 180 avd ? large-signal differential
? sgls131a ? july 2002 ? revised november 2003 21 post office box 655303 ? dallas, texas 75265 typical characteristics large-signal differential voltage amplification ? vs free-air temperature ?75 ?50 ?25 0 25 50 75 100 125 10 100 1 k t a ? free-air temperature ? c v dd = 5 v v ic = 2.5 v v o = 1 v to 4 v r l = 1 m ? r l = 10 k ? avd ? large-signal differential c r l = 1 m ? r l = 10 k ? v dd = 5 v v ic = 0 v v o = 4 v avd ? large-signal differential ? z o output impedance vs frequency v dd = 5 v t a = 25 c a v = 100 a v = 10 a v = 1 figure 29 10 1 0.1 1000 100 100 1 k 10 k 100 k 1 m zo ? output impedance ? o f ? frequency ? hz ? z o output impedance vs frequency v dd = 5 v t a = 25 c a v = 100 a v = 10 a v = 1 figure 30 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 22 post office box 655303 ? dallas, texas 75265 typical characteristics common-mode rejection ratio vs frequency 60 40 20 0 10 100 1 k 10 k cmrr ? common-mode rejection ratio ? db 80 100 100 k 1 m f ? frequency ? hz v dd = 5 v v dd = 5 v 10 m t a = 25 c figure 31 t a ? free-air temperature ? c cmrr ? common-mode rejection ratio ? db common-mode rejection ratio vs free-air temperature 82 78 74 70 86 90 ?75 ?50 ?25 0 25 50 75 100 125 v dd = 5 v v dd = 5 v v ic = 0 v to 2.7 v v ic = ? 5 v to 2.7 v figure 32 40 20 0 10 100 1 k ksvr ? supply-voltage rejection ratio ? db 60 80 f ? frequency ? hz 100 10 k 100 k 1 m 10 m supply-voltage rejection ratio vs frequency k svr v dd = 5 v t a = 25 c k svr+ k svr ? ?20 figure 33 40 20 0 10 100 1 k ksvr ? supply-voltage rejection ratio ? db 60 80 f ? frequency ? hz 100 10 k 100 k 1 m 10 m supply-voltage rejection ratio vs frequency k svr v dd = 5 v t a = 25 c k svr+ k svr ? ?20 figure 34
? sgls131a ? july 2002 ? revised november 2003 23 post office box 655303 ? dallas, texas 75265 typical characteristics ksvr ? supply voltage rejection ratio ? db supply voltage rejection ratio ? vs free-air temperature k svr t a ? free-air temperature ? c ?75 ?50 ?25 0 25 50 75 100 125 100 95 90 85 105 110 v dd = 2.2 v to 8 v v o = 0 v figure 35 012345 67 8 0 0.6 1.2 1.8 2.4 3 idd ? supply current ? ma dd i |v dd | ? supply voltage ? v v o = 0 v no load t a = 25 c t a = ? 55 c t a = 125 c figure 36 tlc2272 supply current ? vs supply voltage figure 37 012345 67 8 0 1.2 2.4 3.6 4.8 6 idd ? supply current ? ma dd i |v dd | ? supply voltage ? v v o = 0 v no load t a = 25 c t a = ? 55 c t a = 125 c tlc2274 supply current ? vs supply voltage figure 38 ?75 ?50 ?25 0 25 50 75 100 125 0 0.6 1.2 1.8 2.4 3 t a ? free-air temperature ? c idd ? supply current ? ma dd i v dd = 5 v v o = 2.5 v v dd = 5 v v o = 0 v tlc2272 supply current ? vs free-air temperature ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 24 post office box 655303 ? dallas, texas 75265 typical characteristics figure 39 ?75 ?50 ?25 0 25 50 75 100 125 0 1.2 2.4 3.6 4.8 6 t a ? free-air temperature ? c idd ? supply current ? ma dd i v dd = 5 v v o = 2.5 v v dd = 5 v v o = 0 v tlc2274 supply current ? vs free-air temperature s sr ? slew rate ? v/ 0 1 2 3 c l ? load capacitance ? pf slew rate vs load capacitance 10 k 1 k 100 10 sr + sr ? 4 5 v dd = 5 v a v = ? 1 t a = 25 c figure 40 3 2 1 4 s sr ? slew rate ? v/ ?75 ?50 ?25 0 25 50 75 100 125 t a ? free-air temperature ? c slew rate ? vs free-air temperature v dd = 5 v r l = 10 k ? c l = 100 pf a v = 1 sr + sr ? 0 5 figure 41 inverting large-signal pulse response 2 1 0 12345 3 4 5 6789 vo ? output voltage ? mv v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = ? 1 0 figure 42 ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 25 post office box 655303 ? dallas, texas 75265 typical characteristics 0 ? 1 ? 3 ? 4 ? 5 4 ? 2 12345 2 1 3 5 6789 vo ? output voltage ? v v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = ? 1 inverting large-signal pulse response 0 figure 43 3 2 1 0 12345 4 5 6789 vo ? output voltage ? v v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf a v = 1 t a = 25 c voltage-follower large-signal pulse response 0 figure 44 voltage-follower large-signal pulse response 0 ?1 4 12345 2 1 3 5 6789 vo ? output voltage ? v v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = 1 0 ?2 ?3 ?5 ?4 figure 45 inverting small-signal pulse response 2.5 2.45 2.4 0.5 1 1.5 2 2.5 2.55 2.6 2.65 3.5 4.5 5 5.5 vo ? output voltage ? v v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = ?1 0 3 4 figure 46
? sgls131a ? july 2002 ? revised november 2003 26 post office box 655303 ? dallas, texas 75265 typical characteristics 0 ?100 0 0.5 1 1.5 2 50 100 2.5 3 3.5 4 vo ? output voltage ? mv v o t ? time ? s inverting small-signal pulse response v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = 1 ?50 figure 47 voltage-follower small-signal pulse response 2.5 2.45 2.4 2.55 2.6 0 0.5 1 1.5 vo ? output voltage ? v v o t ? time ? s 2.65 v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = 1 figure 48 voltage-follower small-signal pulse response 0 ?50 ?100 50 100 0 0.5 1 1.5 vo ? output voltage ? mv v o t ? time ? s v dd = 5 v r l = 10 k ? c l = 100 pf t a = 25 c a v = 1 figure 49 20 10 0 10 100 1 k vn ? equivalent input noise voltage ? nv hz 30 f ? frequency ? hz 40 10 k equivalent input noise voltage vs frequency 50 60 v n nv/ hz v dd = 5 v t a = 25 c r s = 20 ? figure 50
? sgls131a ? july 2002 ? revised november 2003 27 post office box 655303 ? dallas, texas 75265 typical characteristics 20 10 0 10 100 1 k vn ? equivalent input noise voltage ? nv hz 30 f ? frequency ? hz 40 10 k equivalent input noise voltage vs frequency 50 60 v n nv/ hz v dd = 5 v t a = 25 c r s = 20 ? figure 51 ?750 ?1000 246 0 250 810 noise voltage ? nv t ? time ? s noise voltage over a 10 second period 0 v dd = 5 v f = 0.1 hz to 10 hz t a = 25 c 500 750 1000 ?250 ?500 figure 52 integrated noise voltage ? uvrms 1 0.1 100 1 10 100 1 k f ? frequency ? hz integrated noise voltage vs frequency 10 k 100 k v rms calculated using ideal pass-band filter lower frequency = 1 hz t a = 25 c 10 figure 53 0.0001 0.001 100 1 k 10 k 100 k thd + n ? total harmonic distortion plus noise ? % f ? frequency ? hz total harmonic distortion plus noise vs frequency 0.01 0.1 1 v dd = 5 v t a = 25 c r l = 10 k ? a v = 100 a v = 10 a v = 1 figure 54
? sgls131a ? july 2002 ? revised november 2003 28 post office box 655303 ? dallas, texas 75265 typical characteristics figure 55 gain-bandwidth product ? mhz 2.1 2 012345 2.2 2.3 678 |v dd | ? supply voltage ? v 2.4 2.5 gain-bandwidth product vs supply voltage f = 10 khz r l = 10 k ? c l = 100 pf t a = 25 c figure 56 ?75 ?50 ?25 0 25 50 75 100 125 t a ? free-air temperature ? c gain-bandwidth product ? mhz gain-bandwidth product ? vs free-air temperature 1.8 1.6 1.4 2 2.4 2.2 2.6 2.8 3 v dd = 5 v f = 10 khz r l = 10 k ? c l = 100 pf 10 om ? phase margin 10000 c l ? load capacitance ? pf m phase margin vs load capacitance 1000 100 v dd = 5 v t a = 25 c r null = 20 ? r null = 10 ? r null = 0 75 60 45 30 15 0 10 k ? 10 k ? v dd ? v dd + r null c l v i r null = 100 ? r null = 50 ? figure 57 figure 58 3 0 10 gain margin ? db 6 9 10000 c l ? load capacitance ? pf 12 15 gain margin vs load capacitance 1000 100 v dd = 5 v a v = 1 r l = 10 k ? t a = 25 c ? data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various dev ices.
? sgls131a ? july 2002 ? revised november 2003 29 post office box 655303 ? dallas, texas 75265 application information macromodel information macromodel information provided was derived using microsim parts ? , the model generation software used with microsim pspice ? . the boyle macromodel (see note 6) and subcircuit in figure 59 were generated using the tlc227x typical electrical and operating characteristics at t a = 25 c. using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): maximum positive output voltage swing maximum negative output voltage swing slew rate quiescent power dissipation input bias current open-loop voltage amplification unity gain frequency common-mode rejection ratio phase margin dc output resistance ac output resistance short-circuit output current limit note 6: g. r. boyle, b. m. cohn, d. o. pederson, and j. e. solomon, ?macromodeling of integrated circuit operational amplifiers?, ieee journal of solid-state circuits, sc-9, 353 (1974). out + ? + ? + ? + ? + ? + ? + ? + ? + ? .subckt tlc227x 1 2 3 4 5 c1 11 1214e?12 c2 6 760.00e?12 dc 5 53dx de 54 5dx dlp 90 91dx dln 92 90dx dp 4 3dx egnd 99 0poly (2) (3,0) (4,) 0 .5 .5 fb 99 0poly (5) vb vc ve vlp vln 0 + 984.9e3 ?1e6 1e6 1e6 ?1e6 ga 6 011 12 377.0e?6 gcm 0 6 10 99 134e?9 iss 3 10dc 216.oe?6 hlim 90 0vlim 1k j1 11 210 jx j2 12 110 jx r2 6 9100.oe3 rd1 60 112.653e3 rd2 60 122.653e3 r01 8 550 r02 7 9950 rp 3 44.310e3 rss 10 99925.9e3 vad 60 4?.5 vb 9 0dc 0 vc 3 53 dc .78 ve 54 4dc .78 vlim 7 8dc 0 vlp 91 0dc 1.9 vln 0 92dc 9.4 .model dx d (is=800.0e?18) .model jx pjf (is=1.500e?12beta=1.316e-3 + vto=?.270) .ends v cc + rp in ? 2 in + 1 v cc ? vad rd1 11 j1 j2 10 rss iss 3 12 rd2 60 ve 54 de dp vc dc 4 c1 53 r2 6 9 egnd vb fb c2 gcm ga vlim 8 5 ro1 ro2 hlim 90 dip 91 din 92 vin vip 99 7 figure 59. boyle macromodel and subcircuit pspice and parts are trademarks of microsim corporation.

mechanical data mtss001c january 1995 revised february 1999 post office box 655303 ? dallas, texas 75265 pw (r-pdso-g**) plastic small-outline package 14 pins shown 0,65 m 0,10 0,10 0,25 0,50 0,75 0,15 nom gage plane 28 9,80 9,60 24 7,90 7,70 20 16 6,60 6,40 4040064/f 01/97 0,30 6,60 6,20 8 0,19 4,30 4,50 7 0,15 14 a 1 1,20 max 14 5,10 4,90 8 3,10 2,90 a max a min dim pins ** 0,05 4,90 5,10 seating plane 0 8 notes: a. all linear dimensions are in millimeters. b. this drawing is subject to change without notice. c. body dimensions do not include mold flash or protrusion not to exceed 0,15. d. falls within jedec mo-153
important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all products are sold subject to ti?s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ti?s standard warranty. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ti assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ti components. to minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any ti patent right, copyright, mask work right, or other ti intellectual property right relating to any combination, machine, or process in which ti products or services are used. information published by ti regarding third-party products or services does not constitute a license from ti to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alteration is an unfair and deceptive business practice. ti is not responsible or liable for such altered documentation. resale of ti products or services with statements different from or beyond the parameters stated by ti for that product or service voids all express and any implied warranties for the associated ti product or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. following are urls where you can obtain information on other texas instruments products and application solutions: products applications amplifiers amplifier.ti.com audio www.ti.com/audio data converters dataconverter.ti.com automotive www.ti.com/automotive dsp dsp.ti.com broadband www.ti.com/broadband interface interface.ti.com digital control www.ti.com/digitalcontrol logic logic.ti.com military www.ti.com/military power mgmt power.ti.com optical networking www.ti.com/opticalnetwork microcontrollers microcontroller.ti.com security www.ti.com/security telephony www.ti.com/telephony video & imaging www.ti.com/video wireless www.ti.com/wireless mailing address: texas instruments post office box 655303 dallas, texas 75265 copyright ? 2004, texas instruments incorporated

▲Up To Search▲

Price & Availability of TLC227XA-EP

	To Download TLC227XA-EP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .